Holiday Lights

Holiday Lights

Loading...
T Christy Enterprises

PVC Cement, 1 gal Can Low VOC Deep Blue

Part #
CSTRHBVGL6
MFG #
RH-RHBV-GL-6
T Christy Enterprises

PVC Cement, 1 gal Can Low VOC Deep Blue

Part #
CSTRHBVGL6
MFG #
RH-RHBV-GL-6
Login or Register to view pricing and availability
Free Shipping on Orders over $149

Product Image Feedback

Shop for Christy's Red Hot Blue Glue

  • Contractor preferred
  • Medium body and fast setting
  • Can be used without primer(if local codes permit)

Product Details

  • Blue in color
  • All classes and schedules through 6" diameter interference fit
  • Schedule 80 through 4"

Features and Benefits

Christy's Red Hot Blue Glue® is a very aggressive, deep blue, medium-bodied, very fast-setting PVC solvent cement. Christy's Red Hot Blue Glue® is the industry's highest quality Blue Glue, from the leading producer of high-performance solvent cement. For use in plumbing, industrial, irrigation, agricultural, municipal, or pool and spa applications including PVC foam core.

DIRECTIONS: For use on PVC plastics. Stir and use as is. DO NOT THIN CEMENT. Discard if jellied. Use within 3 years of the date stamp on the can.

1) Cut pipe square, deburr, and wipe clean. Make a trial dry-fit – pipe should fit snugly 1/3 – 2/3 snugly into the fitting. Use an adequate sized applicator at last 1/2” size of pipe diameter Dauber, brush, roller or swab. Apply Christy’s Primer if required by local code. Uniform Plumbing Code requires the use of a purple primer. CAN BE USED WITHOUT A PRIMER IF LOCAL CODES PERMIT for non-pressure systems up to 6″ and pressure systems below 4″.

2) Apply a full, even coat of cement to the outside of the pipe and a medium coat of cement on the inside of the fitting. Coat pipe a second time. Quickly assemble the joint while cement is still fluid on both parts. If dry, pipe and fitting must be re-coated. Push and rotate pipe into the fitting until pipe bottoms in the socket. Hold together until joint sets (approx. 30 seconds).

3) Remove excess cement. Leave joint undisturbed for at least 10 minutes. Full joint strength should be reached within 24 hours depending upon temperature and humidity. See installation Guide for product set and cure time and additional information. STORE BETWEEN 40 °F (4 °C) and 110 °F (43 °C) DO NOT TEST WITH AIR.

INSTRUCCIONES: Para aplicar en plásticos de PVC. Revuélvalo y utilícelo como está. No lo disuelva. Deséchelo si se halla en estado de gel o fibroso. Utilícelo antes de que transcurran 3 años de la fecha impresa en la base de la lata.

1) Corte el tubo a escuadra, quítele las rebabas y límpielo con un paño limpio y seco. Haga una prueba de encajadura en seco en todas las juntas antes de proceder (1/3 ó 2/3 del tubo deberían entrar cómodamente dentro del conector para la unión entre las piezas). Utilice un aplicador del tamaño adecuado. Para los tubos de 2-1/2” y más grandes se necesita una brocha o un rodillo. El estándar de especificación IS8 (tubos de PVC para agua potable) de IAPMO establece como obligatoria la aplicación de una pintura de color morado. COMPLETE LOS PASOS 2 y 3 EN UN LAPSO DE TREINTA SEGUNDOS PARA QUE LA JUNTA QUEDE FIRME

2) Aplique una capa de cemento abundante y uniforme en la parte externa del extremo macho del tubo y una capa intermedia en la parte interna del conector que va a unir. No aplique demasiado pegamento ni deje zonas sin aplicarlo. Es necesario aplicar dos capas en el extremo del tubo antes del ensamblaje; además, el tubo debe estar “húmedo” durante el ensamblaje. Empuje y haga girar el tubo hacia el interior del conector (1/4 de giro) hasta que se asiente en éste. Manténgalos unidos hasta que se seque la unión (aproximadamente 30 segundos). Si el tubo está seco, debe aplicársele una nueva capa.

3) Quite el exceso de cemento y deje reposar la unión por lo menos durante 10 minutos. La junta debería alcanzar la resistencia máxima en 24 horas, según la temperatura y la humedad existentes. El tubo puede probarse con agua (solamente) a 75 psi, una hora después de la unión. GUARDELO Y UTILICELO A UNA TEMPERATURA ENTRE 40 °F Y 110 °F

This product is not for use in a system using or being tested with compressed air or gases.

Brand:
T Christy Enterprises
Cleaner/Primer Type:
Solvent Cement
Container Size:
1 gal
Density:
>2 (Air=1) Vapor
Form:
Medium Syrupy Liquid
Label Color:
Deep Blue
Odor/Scent:
Ketone
Specific Gravity:
0.955 +/- 0.04